Dodo scales for dummies...
Moderator: Moderators
- stevespo
- Member
- Posts: 584
- Joined: August 11th, 2014, 8:07 pm
- THS Average: 225
- Positive Axis Point: 5.75" x + 3/8"
- Speed: 17+ off hand (camera)
- Rev Rate: 375
- Axis Tilt: 12
- Axis Rotation: 45
- Heavy Oil Ball: Phaze II, Altered Reality
- Medium Oil Ball: IQ Tour Nano, Zen, Phase III
- Light Oil Ball: Electrify Pearl
Dodo scales for dummies...
Just for clarification, the dummy is me.
I'm doing some experimenting with drilling and layouts at home, and naturally I'd like to be sure that my equipment meets the USBC static weight requirements. Local pro shop has been none too helpful in this regard, so I've been trying to find a used dodo scale. The AMFs show up on eBay, but the prices seem high and I'm always outbid.
So, I had some time in the shop yesterday and wondered if I couldn't put something together with some scrap phenolic ply, 8020 extrusion and ball bearings (for fulcrum).
It seems to work as expected. I can balance a ball, then change the orientation and it will lose balance (it seems to be sensitive to 1/20th of an ounce).
I can then add small counterweights and get it back into balance.
Now, I need to fix the weight positions and calibrate it so I know when it's within 1 oz and 3 oz. I will add some adjustable (sliding) weights to the rail and mark the positions.
Am I missing something painfully obvious here?
The commercial scales are well designed and made, but this is not rocket science - right?
I'm not looking to accurately measure the total weight, just to make sure my offsets are within range.
Thanks!
Steve
I'm doing some experimenting with drilling and layouts at home, and naturally I'd like to be sure that my equipment meets the USBC static weight requirements. Local pro shop has been none too helpful in this regard, so I've been trying to find a used dodo scale. The AMFs show up on eBay, but the prices seem high and I'm always outbid.
So, I had some time in the shop yesterday and wondered if I couldn't put something together with some scrap phenolic ply, 8020 extrusion and ball bearings (for fulcrum).
It seems to work as expected. I can balance a ball, then change the orientation and it will lose balance (it seems to be sensitive to 1/20th of an ounce).
I can then add small counterweights and get it back into balance.
Now, I need to fix the weight positions and calibrate it so I know when it's within 1 oz and 3 oz. I will add some adjustable (sliding) weights to the rail and mark the positions.
Am I missing something painfully obvious here?
The commercial scales are well designed and made, but this is not rocket science - right?
I'm not looking to accurately measure the total weight, just to make sure my offsets are within range.
Thanks!
Steve
You do not have the required permissions to view the files attached to this post.
16 mph (14-14.5 on monitor), 375 rpm, PAP 5 1/2 x 3/8 up, AT: 12*, AR: 45*
Re: Dodo scales for dummies...
What you have looks very close.
Positioning the weights on the right side is going to be a task.
I don't know what your budget is but have you seen
http://www.shop.jayhawkbowling.com/Holt ... 5-6100.htm
$450 is a lot less expensive that you'll find for most of the dodo scales.
Positioning the weights on the right side is going to be a task.
I don't know what your budget is but have you seen
http://www.shop.jayhawkbowling.com/Holt ... 5-6100.htm
$450 is a lot less expensive that you'll find for most of the dodo scales.
Re: Dodo scales for dummies...
From the pictures you've done a great job. The dodo scale is not actually for weight but is a comparator.
All you need now is some small weights, 1,2 and 3 oz. To calibrate it simply place one weight the 3 oz on the centre of the ball in the ring, balance with the large weights and put the 1 & 2 on top of each other, on the slide and mark the positions, take the 1 off and move the 2 away from the ring end until it balances and you have found the 1 oz mark.
It's linear so you should be able to mark from 0 to 3 oz easily.
If your scale can measure to 1/20 of an oz you will have a very accurate piece of kit....as good as if not better than the Kaufman scales.
Could be a great business opportunity!!!
All you need now is some small weights, 1,2 and 3 oz. To calibrate it simply place one weight the 3 oz on the centre of the ball in the ring, balance with the large weights and put the 1 & 2 on top of each other, on the slide and mark the positions, take the 1 off and move the 2 away from the ring end until it balances and you have found the 1 oz mark.
It's linear so you should be able to mark from 0 to 3 oz easily.
If your scale can measure to 1/20 of an oz you will have a very accurate piece of kit....as good as if not better than the Kaufman scales.
Could be a great business opportunity!!!
Revs ~350 Tilt ~16* Speed 17-18 off the hand Rotation 30-75
- river800
- Senior Member
- Posts: 1056
- Joined: November 19th, 2010, 12:11 am
- THS Average: 202
- Preferred Company: Storm/radical
- Location: Coeur D A'lene, ID
Re: Dodo scales for dummies...
That is a really cool scale. Definitely affordable for someone either needing a cheaper option to replace something or someone who is just starting out.MWhite wrote:What you have looks very close.
Positioning the weights on the right side is going to be a task.
I don't know what your budget is but have you seen
http://www.shop.jayhawkbowling.com/Holt ... 5-6100.htm
$450 is a lot less expensive that you'll find for most of the dodo scales.
Stats:
Right handed
Pap is 4 3/4 x 3/8 up currently
Speed around 16.5 off hand
Tilt in the 14-16* range
Rev rate: around 325 - 350 or so
Axis rotation in the 25-70* range
I bowl on Brunswick synthetics. Ths...
Right handed
Pap is 4 3/4 x 3/8 up currently
Speed around 16.5 off hand
Tilt in the 14-16* range
Rev rate: around 325 - 350 or so
Axis rotation in the 25-70* range
I bowl on Brunswick synthetics. Ths...
- stevespo
- Member
- Posts: 584
- Joined: August 11th, 2014, 8:07 pm
- THS Average: 225
- Positive Axis Point: 5.75" x + 3/8"
- Speed: 17+ off hand (camera)
- Rev Rate: 375
- Axis Tilt: 12
- Axis Rotation: 45
- Heavy Oil Ball: Phaze II, Altered Reality
- Medium Oil Ball: IQ Tour Nano, Zen, Phase III
- Light Oil Ball: Electrify Pearl
Re: Dodo scales for dummies...
Thanks for the feedback and calibration advice. I needed some confirmation before I spent any more time on it.
I'm going to turn some brass weights and I'll dial in a couple of 1 oz, 2 oz, 3 oz. I might also make 1 lb, 3 lb, and 5 lbs for the counterweight at the 2x position.
I have lots of scrap aluminum, but the density of the brass makes for a more compact weight.
I couldn't decide whether to sit them on top of the bar, or hang them from below, but on top should work out fine.
I really like the idea for the Holtzman, but it was out of my budget. Given that it was a new design and patent pending, I wanted to DIY the tried and true dodo.
If there was enough interest I could probably put together some kits, but I'm not looking for a side business. I barely have time to bowl!
Let's see how the refinements work out and see how it goes. I'd be happy to provide the CAD files when the bugs are worked out.
Steve
I'm going to turn some brass weights and I'll dial in a couple of 1 oz, 2 oz, 3 oz. I might also make 1 lb, 3 lb, and 5 lbs for the counterweight at the 2x position.
I have lots of scrap aluminum, but the density of the brass makes for a more compact weight.
I couldn't decide whether to sit them on top of the bar, or hang them from below, but on top should work out fine.
I really like the idea for the Holtzman, but it was out of my budget. Given that it was a new design and patent pending, I wanted to DIY the tried and true dodo.
If there was enough interest I could probably put together some kits, but I'm not looking for a side business. I barely have time to bowl!
Let's see how the refinements work out and see how it goes. I'd be happy to provide the CAD files when the bugs are worked out.
Steve
16 mph (14-14.5 on monitor), 375 rpm, PAP 5 1/2 x 3/8 up, AT: 12*, AR: 45*
- LabRat
- Pro Shop
- Posts: 1170
- Joined: July 16th, 2011, 2:12 pm
- THS Average: 208
- Preferred Company: Storm
- Location: Townsville, Australia
Re: Dodo scales for dummies...
I'm not sure putting the weight on the ball is correct, as the weight moves from the inside to the outside of the balance as you weigh a ball. I would calibrate it using a NIB ball with a known top weight. Zeroing the balance with the top weight centred then turning it out 90* should result in a weight change of half the top weight. Alternatively you could move a 1 oz weight from the outside to the inside of the ring.
Chemistry is like cooking - just don't lick the spoon.
Re: Dodo scales for dummies...
You are missing the point. This is a comparator and the 3 oz centred on the ball simply makes sure that it does not fall off. The important part is to balance it with the two other weights (2+1) first, then balance it again with only the 2 oz weight further away on the beam. The different points give you the starting point to marking the beam. The one oz weight could then be used further up the beam to give one more mark just to ensure the distances and weights were linear.LabRat wrote:I'm not sure putting the weight on the ball is correct, as the weight moves from the inside to the outside of the balance as you weigh a ball. I would calibrate it using a NIB ball with a known top weight. Zeroing the balance with the top weight centred then turning it out 90* should result in a weight change of half the top weight. Alternatively you could move a 1 oz weight from the outside to the inside of the ring.
The last piece of advice would be to use two clear plastic rulers and glue them to the beam with a space between them so that the 1 oz weight could slide in the space, back and forth between the marks.
Revs ~350 Tilt ~16* Speed 17-18 off the hand Rotation 30-75
- stevespo
- Member
- Posts: 584
- Joined: August 11th, 2014, 8:07 pm
- THS Average: 225
- Positive Axis Point: 5.75" x + 3/8"
- Speed: 17+ off hand (camera)
- Rev Rate: 375
- Axis Tilt: 12
- Axis Rotation: 45
- Heavy Oil Ball: Phaze II, Altered Reality
- Medium Oil Ball: IQ Tour Nano, Zen, Phase III
- Light Oil Ball: Electrify Pearl
Re: Dodo scales for dummies...
This is exactly what I was trying to wrap my head around.kart300 wrote: You are missing the point. This is a comparator and the 3 oz centred on the ball simply makes sure that it does not fall off. The important part is to balance it with the two other weights (2+1) first, then balance it again with only the 2 oz weight further away on the beam. The different points give you the starting point to marking the beam. The one oz weight could then be used further up the beam to give one more mark just to ensure the distances and weights were linear.
When you calibrate the adjustable (sliding) weight on the beam side, are there any assumptions about where the center of mass is on the ball side?
When you turn an asymmetrically weighted ball 90 degrees, the CM will shift one way or the other.
Where that CM falls will be different on every ball, so my thinking was that the beam (counterweight) would have to be calibrated using a known weight difference centered in the middle of the ball.
Otherwise, a 1 oz difference near the cover seems like it would have a greater effect than a 1 oz difference near the core.
Given that it's averaged across the hemisphere and we're talking small amounts, perhaps it's not that critical?
Steve
16 mph (14-14.5 on monitor), 375 rpm, PAP 5 1/2 x 3/8 up, AT: 12*, AR: 45*
- stevespo
- Member
- Posts: 584
- Joined: August 11th, 2014, 8:07 pm
- THS Average: 225
- Positive Axis Point: 5.75" x + 3/8"
- Speed: 17+ off hand (camera)
- Rev Rate: 375
- Axis Tilt: 12
- Axis Rotation: 45
- Heavy Oil Ball: Phaze II, Altered Reality
- Medium Oil Ball: IQ Tour Nano, Zen, Phase III
- Light Oil Ball: Electrify Pearl
Re: Dodo scales for dummies...
How the weight is distributed is pretty critical.stevespo wrote:Otherwise, a 1 oz difference near the cover seems like it would have a greater effect than a 1 oz difference near the core.
Given that it's averaged across the hemisphere and we're talking small amounts, perhaps it's not that critical?
As you'd expect, a 1 oz weight on the left edge requires proportionally more offset on the beam for it to balance.
I calibrated the beam in 1 oz increments, with the weights on the midpoint/centerline of the bowling ball.
Then I moved 1 oz to the outer edge, and it then balanced at about the 1.6 oz mark on my beam.
The distance from the weight to the fulcrum changed from 6.5" to (roughly) 10.75" and 10.75/6.5 = 1.65 so the ratios appear correct (eyeballing it).
Steve
You do not have the required permissions to view the files attached to this post.
16 mph (14-14.5 on monitor), 375 rpm, PAP 5 1/2 x 3/8 up, AT: 12*, AR: 45*
-
- Trusted Source
- Posts: 3174
- Joined: January 18th, 2010, 9:21 pm
Re: Dodo scales for dummies...
JayHawk has a chart where it shows the difference between hanging a counter balance at the edge of the ball v.s. the Kaufman. The Kaufman is off by about 1/4 of an oz for every 1 oz of wt. hanging on the edge of the ball (weighed at the edge of the ball, 2 1/4 oz is close to 3 oz on the Kaufman) with the center of the ball as the balance point. I would be curious if the new Holtzman is comparable to the Kaufman or to the old JayHawk?
Have you seen this thread?: viewtopic.php?t=6474" onclick="window.open(this.href);return false;
(see #24 for the chart from JayHawk)
Have you seen this thread?: viewtopic.php?t=6474" onclick="window.open(this.href);return false;
(see #24 for the chart from JayHawk)
- stevespo
- Member
- Posts: 584
- Joined: August 11th, 2014, 8:07 pm
- THS Average: 225
- Positive Axis Point: 5.75" x + 3/8"
- Speed: 17+ off hand (camera)
- Rev Rate: 375
- Axis Tilt: 12
- Axis Rotation: 45
- Heavy Oil Ball: Phaze II, Altered Reality
- Medium Oil Ball: IQ Tour Nano, Zen, Phase III
- Light Oil Ball: Electrify Pearl
Re: Dodo scales for dummies...
Yes, I've seen that thread and your wooden prototype inspired me to give it a try.
Sure wish I could find a used Jayhawk, AMF, etc for under $250, how did you manage $25? Great deal!
Thanks,
Steve
Sure wish I could find a used Jayhawk, AMF, etc for under $250, how did you manage $25? Great deal!
Thanks,
Steve
16 mph (14-14.5 on monitor), 375 rpm, PAP 5 1/2 x 3/8 up, AT: 12*, AR: 45*
-
- Member
- Posts: 370
- Joined: June 24th, 2010, 2:48 am
- THS Average: 228
- Positive Axis Point: 5.5
- Speed: 16.5
- Rev Rate: 300
- Heavy Oil Ball: Wicked Siege, Perfection X
- Medium Oil Ball: Wicked Siege x2 Speed Master
- Light Oil Ball: Slingshot, Wicked Siege
- Preferred Company: Brunswick/Revolution, Morich
- Location: Arkansas
Re: Dodo scales for dummies...
Very cool scale thread. Scales are so expensive because they are industry specific and the market is small. Same for the determinator, oil extraction devices and many other tools used for bowling. In many cases it is items that are re purposed and the prices raised for profit.
After seeing the digital scale that is available I started playing around with using two digital scales and a plank board between the two with the ball sitting in the middle. Only had a about a week with the two scales I was trying. I may attempt again when I know I am going to have more time to try and work it out.
After seeing the digital scale that is available I started playing around with using two digital scales and a plank board between the two with the ball sitting in the middle. Only had a about a week with the two scales I was trying. I may attempt again when I know I am going to have more time to try and work it out.
"today I went shopping and talk is still cheap"
- stevespo
- Member
- Posts: 584
- Joined: August 11th, 2014, 8:07 pm
- THS Average: 225
- Positive Axis Point: 5.75" x + 3/8"
- Speed: 17+ off hand (camera)
- Rev Rate: 375
- Axis Tilt: 12
- Axis Rotation: 45
- Heavy Oil Ball: Phaze II, Altered Reality
- Medium Oil Ball: IQ Tour Nano, Zen, Phase III
- Light Oil Ball: Electrify Pearl
Re: Dodo scales for dummies...
Yeah, I hope we can collectively brainstorm and come up with options for the hobbyist driller. I'm happy to support our great vendors, but can't justify $500-1000+ for something that gets used a handful of times a year. I also can't wait months until I manage to win something on eBay, either. It puts us in an awkward spot.
Anyway, I balanced my new Exile over the weekend and (I think) it worked out very nicely. I was near the limit for side weight and just over for finger weight, which I knew based on the high CG location. Top/bottom was fine. I removed about .3 oz by drilling the ring finger 1/2 inch deeper and that brought both into the 1 oz compliance.
I will verify with my pro shop but I am pretty confident it's all working as it should be.
Steve
Anyway, I balanced my new Exile over the weekend and (I think) it worked out very nicely. I was near the limit for side weight and just over for finger weight, which I knew based on the high CG location. Top/bottom was fine. I removed about .3 oz by drilling the ring finger 1/2 inch deeper and that brought both into the 1 oz compliance.
I will verify with my pro shop but I am pretty confident it's all working as it should be.
Steve
16 mph (14-14.5 on monitor), 375 rpm, PAP 5 1/2 x 3/8 up, AT: 12*, AR: 45*
Re: Dodo scales for dummies...
Wow. Over the past 6 months I built my own bowling ball drill press and jig, and can drill balls with hole pitches to within 1/16 of inch accuracy, but the scale is that I don't have. I'll definitely try making one of these now that I found this post. Anyone have any updates - or I'll just follow the pictures and discussion.
- stevespo
- Member
- Posts: 584
- Joined: August 11th, 2014, 8:07 pm
- THS Average: 225
- Positive Axis Point: 5.75" x + 3/8"
- Speed: 17+ off hand (camera)
- Rev Rate: 375
- Axis Tilt: 12
- Axis Rotation: 45
- Heavy Oil Ball: Phaze II, Altered Reality
- Medium Oil Ball: IQ Tour Nano, Zen, Phase III
- Light Oil Ball: Electrify Pearl
Re: Dodo scales for dummies...
That is as far as I took it. I was eventually able to borrow a Kaufman, and finally purchased a Holtzman (digital). Although the Kaufman has a certain mechanical appeal and was fun to use, the Holtzman is far faster and easier (and it takes up a lot less shelf space). That's one purchase I'm very happy with.
If you're interested in my prototype, I could box up the parts and send them your way. You'd at least have something to start with and play around. You'd have to calibrate with some weights, but it's plenty accurate when you get the hang of it. Send me a PM.
Steve
If you're interested in my prototype, I could box up the parts and send them your way. You'd at least have something to start with and play around. You'd have to calibrate with some weights, but it's plenty accurate when you get the hang of it. Send me a PM.
Steve
16 mph (14-14.5 on monitor), 375 rpm, PAP 5 1/2 x 3/8 up, AT: 12*, AR: 45*
-
- Member
- Posts: 915
- Joined: January 19th, 2010, 12:53 am
- THS Average: 210
- Positive Axis Point: 4 3/4" over 1/4" up
- Speed: 17 mph
- Axis Tilt: 17
- Axis Rotation: 45+
- Heavy Oil Ball: Idol, Show-off
- Medium Oil Ball: Venom Shock, Rhodman,
- Light Oil Ball: Phobia, White Hot Badger
- Location: Northern California
Re: Dodo scales for dummies...
I tried to build a holtzman style scale out of wood. You can buy the exact scale they use online for about $30. I could never get it to weigh the same twice though. I think the wood flexing didn't help and the pivot point wasn't the best. I just gave up on it. If you had some good material, I think it could be done pretty easily. Calibrating might be a little tricky though.stevespo wrote:That is as far as I took it. I was eventually able to borrow a Kaufman, and finally purchased a Holtzman (digital). Although the Kaufman has a certain mechanical appeal and was fun to use, the Holtzman is far faster and easier (and it takes up a lot less shelf space). That's one purchase I'm very happy with.
If you're interested in my prototype, I could box up the parts and send them your way. You'd at least have something to start with and play around. You'd have to calibrate with some weights, but it's plenty accurate when you get the hang of it. Send me a PM.
Steve
Right Handed, 16-17 mph off hand (14 -15 mph on Qubica reading) ,350 rpm,PAP 4 3/4 x 1/4 up, 17 deg axis tilt, varied rotational axis deg.. usually 45+
Book Average 210+
Book Average 210+
Re: Dodo scales for dummies...
I bought the KMT dodo scale that comes with a ball jig. $320 to my door. Drilled 2 balls, weighed them (about .6 of finger and .5 of side). Took them to RENO last week. I watched the guy weight them, same result. They passed inspection. Best bang for buck in my opinion.
-Mark-
YABA/ABC/USBC Sanctioned:
3's - 23
8's - 11 (846 high)
YABA/ABC/USBC Sanctioned:
3's - 23
8's - 11 (846 high)
Re: Dodo scales for dummies...
If you want to see DIY scales, look at herculino's. That's how you do DIY!
Check out the things he made here:
viewtopic.php?f=7&t=7618
Check out the things he made here:
viewtopic.php?f=7&t=7618
"REMEMBER, it isn't how much the ball hooks, it's where."
Re: Dodo scales for dummies...
Hi everyone,
I am new to this forum and I am trying to find a topic that is most related to my question so probably this is the right one.
I am planning a balance scale with which you can use one of those kitchen digital scales.
The prototype I made works very well with a digital scale bought in a Chinese shop for few euros.
But in order to match the Kaufman scale I need to know how the Kaufman is calibrated.
So does anyone know how it is calibrated?
Thanks guys.
Remo
I am new to this forum and I am trying to find a topic that is most related to my question so probably this is the right one.
I am planning a balance scale with which you can use one of those kitchen digital scales.
The prototype I made works very well with a digital scale bought in a Chinese shop for few euros.
But in order to match the Kaufman scale I need to know how the Kaufman is calibrated.
So does anyone know how it is calibrated?
Thanks guys.
Remo
Re: Dodo scales for dummies...
Hello,
I want to buy those scales https://tacunasystems.com/product-category/scales/" onclick="window.open(this.href);return false; , could I find them on ebay with shipping to France ?
Thanks !
I want to buy those scales https://tacunasystems.com/product-category/scales/" onclick="window.open(this.href);return false; , could I find them on ebay with shipping to France ?
Thanks !
Last edited by Patricio on August 2nd, 2019, 4:04 pm, edited 1 time in total.