mania
Moderator: Moderators
-
- Member
- Posts: 27
- Joined: February 27th, 2010, 4:24 pm
- THS Average: 205
- Positive Axis Point: over5 up1/2
- Speed: 15
- Axis Tilt: 15
- Axis Rotation: 20
- Heavy Oil Ball: brunswick3.5
- Medium Oil Ball: brunswick 2.5 track 930
- Light Oil Ball: track 920a
mania
i have the mania coming tomorrow and want some input on drilling it, if i want to use it for deep inside would i use the double thumb layout witch for me is 58x4x30 or a lower val number be better.i have lower rev about 200 and tilt about 10* so i know i cannot move to deep.
-
- Trusted Source
- Posts: 3174
- Joined: January 18th, 2010, 9:21 pm
Re: mania
they will want your ball speed.
-
- Trusted Source
- Posts: 3174
- Joined: January 18th, 2010, 9:21 pm
Re: mania
the double thumb is about as strong as you can get. You don't want more val angle on a double thumb, if that was your question. the 30 degree val actually becomes a 20 degree val with the double thumb.
-
- Trusted Source
- Posts: 3174
- Joined: January 18th, 2010, 9:21 pm
Re: mania
since you are only asking for input, (DON'T DRILL THE BALL UNTIL YOU TALK TO THE PROFESSIONALS) I understand the mania is an early arcing ball with a lot of continuation. On that particular ball with your ballspeed you could possibly get more length with a strong backend by going a little larger on your drilling angle and using a P3 hole, but then you run the risk of over-skidding your breakpoint if there is a lot of oil inside. You didn't say if you wanted to play inside because of the pattern breaking down some or why?
-
- Member
- Posts: 27
- Joined: February 27th, 2010, 4:24 pm
- THS Average: 205
- Positive Axis Point: over5 up1/2
- Speed: 15
- Axis Tilt: 15
- Axis Rotation: 20
- Heavy Oil Ball: brunswick3.5
- Medium Oil Ball: brunswick 2.5 track 930
- Light Oil Ball: track 920a
Re: mania
our home shot for me is up the 8-10 when we go to other house mainly wood i need to move in it seem the shot is a little less over under. thanks for your thoughts
- MathIsTruth
- Industry Professional
- Posts: 548
- Joined: January 19th, 2010, 5:18 pm
- Preferred Company: MoRich/Radical
- Location: Washington, WV
Re: mania
You may want to include your axis rotation as well, I see you included your ball speed at 15. Good luck with the Mania!!dlj2214 wrote:i have the mania coming tomorrow and want some input on drilling it, if i want to use it for deep inside would i use the double thumb layout witch for me is 58x4x30 or a lower val number be better.i have lower rev about 200 and high tilt about 10* so i know i cannot move to deep.
- Mo Pinel
- Rest In Peace
- Posts: 10054
- Joined: January 26th, 2010, 6:10 pm
- Preferred Company: MoRich, & now RADICAL BT
- Location: Richmond, VA
Re: mania
Please "Double Thumb" the mania. Max out the size of the balance hole! Add surface if necessary.dlj2214 wrote:i have the mania coming tomorrow and want some input on drilling it, if i want to use it for deep inside would i use the double thumb layout witch for me is 58x4x30 or a lower val number be better.i have lower rev about 200 and tilt about 10* so i know i cannot move to deep.
Rest In Peace (1942-2021)