Board index » Mo & Friends » Ball & Layout Advice




Post new topic Reply to topic  [ 8 posts ] 
Author Message
 Post subject: Layout Help Needed
 Posted: Fri Apr 06, 2018 1:11 pm Post Number: #1 Post
Offline
Member

Joined: April 18, 2012
Posts: 48
Reputation: 3
Reputation Power: 1
I recently used the Bowlers ID and got updated delivery stats. Im unsure how accurate it really is but i attached the results. My old PAP was 5" and 1-1/8" up and when measured before, rev rate was in 320s, tilt was 14 and rotation was 62.

Could I have my long and strong, becnchmark, control, strong and low falre drillings for my new stats?

Thanks,

Dustin


You do not have the required permissions to view the files attached to this post.


Top 
 Profile  
Reply with quote  
 Post subject: Re: Layout Help Needed
 Posted: Fri Apr 06, 2018 4:21 pm Post Number: #2 Post
Offline
BCU Graduate Layouts
User avatar

Joined: April 4, 2011
Posts: 3212
Location: Michigan
Reputation: 275
Reputation Power: 3
It is going to be a couple of days before I can get to your request.
Posting a reply so it
will be in my post list when I get back to my computer.

_________________
Eric Hartwell

Right Handed
PAP 4.75" up 1/2"
45* rotation
12* tilt
330 rev rate
16 mph off hand


Top 
 Profile  
Reply with quote  
 Post subject: Re: Layout Help Needed
 Posted: Mon Apr 09, 2018 11:49 am Post Number: #3 Post
Offline
Member

Joined: April 18, 2012
Posts: 48
Reputation: 3
Reputation Power: 1
bump


Top 
 Profile  
Reply with quote  
 Post subject: Re: Layout Help Needed
 Posted: Mon Apr 09, 2018 10:15 pm Post Number: #4 Post
Offline
BCU Graduate Layouts
User avatar

Joined: April 4, 2011
Posts: 3212
Location: Michigan
Reputation: 275
Reputation Power: 3
First thing I would do Is verify your PAP on a ball that has significant amount of flare. I am assuming the Bowler ID was not with your own ball, it was on a ball that did not flare, is that correct?

You are slightly speed dominant with higher rotation.
Sweetspot 90* Totals, 1.25:1 Ratio

Asymmetrical Layouts
Totally Strong ............. 55-4.5-55
Midlane ..................... 30-4.5-40
Benchmark ................ 50-4.25-40
Long and Strong ......... 70-4.25-40
Control ...................... 50-3.75-60
low flare .................... 70-2.25-40

Symmetrical Layouts (drilling angle to the Cg)
Totally Strong ............. Double Thumb layout
Midlane ..................... 55-4-35 balance hole 1.5" below midline on the VAL
Benchmark ................ 55-4-35 P3
Long and Strong ......... 75-4.25-35
Control ...................... 65-4.25-55 balance hole 2" below midline on the VAL
low flare .................... 70-5-35

_________________
Eric Hartwell

Right Handed
PAP 4.75" up 1/2"
45* rotation
12* tilt
330 rev rate
16 mph off hand


Top 
 Profile  
Reply with quote  
 Post subject: Re: Layout Help Needed
 Posted: Mon Apr 09, 2018 10:19 pm Post Number: #5 Post
Offline
Member

Joined: April 18, 2012
Posts: 48
Reputation: 3
Reputation Power: 1
Yes bowlers ID is on non flaring urethane ball that doesn't have my pitches or span


Top 
 Profile  
Reply with quote  
 Post subject: Re: Layout Help Needed
 Posted: Mon Apr 09, 2018 11:12 pm Post Number: #6 Post
Offline
BCU Graduate Layouts
User avatar

Joined: April 4, 2011
Posts: 3212
Location: Michigan
Reputation: 275
Reputation Power: 3
I would definitely mark out your old PAP you had mentioned on a flaring ball and see how accurate that is, adjust as necessary before drilling anything up.

_________________
Eric Hartwell

Right Handed
PAP 4.75" up 1/2"
45* rotation
12* tilt
330 rev rate
16 mph off hand


Top 
 Profile  
Reply with quote  
 Post subject: Re: Layout Help Needed
 Posted: Tue Apr 10, 2018 3:38 pm Post Number: #7 Post
Offline
Member

Joined: April 18, 2012
Posts: 48
Reputation: 3
Reputation Power: 1
Measured pap on high flare ball last night, my old PAP is correct. 5" over, 1-1/8" up.


Top 
 Profile  
Reply with quote  
 Post subject: Re: Layout Help Needed
 Posted: Tue Apr 10, 2018 7:22 pm Post Number: #8 Post
Offline
BCU Graduate Layouts
User avatar

Joined: August 31, 2014
Posts: 647
Location: Tucson, AZ
Reputation: 121
Reputation Power: 2
I'm concerned that your axis tilt may different with your grip specs than listed from bowlerID.
Using an Armadillo to measure your PAP, what is the distance from your PAP to the first oil ring (closest to the gripline)? Armadillo has embossed lines on the surface in inches for finding this value.

_________________
Benchmark Bowling Pro Shop
Byron

RH
PAP: 5.625" x 0
REVRATE: 360
SPEED: 17mph at release
AR: 55º
AT: 7º


Top 
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
 
Post new topic Reply to topic  [ 8 posts ] 

Board index » Mo & Friends » Ball & Layout Advice


 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to: