Board index » Mo & Friends » General Discussion


Forum rules


Ask Mo Pinel and the bowling industry's best your questions, and get straight answers.
This forum is moderated exclusively by Mo & Friends.



Post new topic Reply to topic  [ 26 posts ]  Go to page Previous  1, 2
Author Message
 Post subject: Re: Pin to PAP distances
 Posted: Mon Jan 29, 2018 2:45 am Post Number: #21 Post
Offline
Moderator
User avatar

Joined: April 26, 2007
Posts: 4246
Location: Malta, NY
Reputation: 933
Reputation Power: 10
rocketman1964 wrote:

Thanks MegaMav, really appreciate your help.


My pleasure, I added an additional note to adjust VAL to 40 if need be, you probably will with your PAP and the short pin.

_________________
Please press the Image button if you feel I've been helpful.

“When you prepare for everything, you’re ready for anything.” - Bill Walsh


Top 
 Profile  
Reply with quote  
 Post subject: Re: Pin to PAP distances
 Posted: Mon Jan 29, 2018 10:15 am Post Number: #22 Post
Offline
Member

Joined: May 3, 2015
Posts: 54
Location: Cocoa Beach, FL
Reputation: 0
Reputation Power: 1
MegaMav wrote:

My pleasure, I added an additional note to adjust VAL to 40 if need be, you probably will with your PAP and the short pin.


Just for my understanding, is the change in VAL due to my specs, or for the static imbalance of the ball, or both? You said if need be, and I just want to be clear as to what that means. My initial thoughts is it is for static imbalance only, that I would determine, after laying it out and weighing before drilling, if I would need to go to 40. Still new to this drilling stuff. Thanks.

_________________
Rob

RH Wiki Fit:
MF 4 7/16, 3/8 L, 1/8 R
RF 4 3/8, 1/2 R, 1/8 R
Thumb 1/4 Rev, 1/4 L
Axis Tilt 10 deg
Axis Rotation 70 deg
260 Revs
PAP 5 7/8 over 3/4 up
Speed 14.5 - 15.5 Monitor
House/Sport or PBA on rare occasion


Top 
 Profile  
Reply with quote  
 Post subject: Re: Pin to PAP distances
 Posted: Mon Jan 29, 2018 2:15 pm Post Number: #23 Post
Offline
Moderator
User avatar

Joined: April 26, 2007
Posts: 4246
Location: Malta, NY
Reputation: 933
Reputation Power: 10
Both. With the layout and your PAP the CG may end up too high to drill the fingers deep enough to have room for a balance hole which is part of Asym F. 40 will cheat it around 1/2".

_________________
Please press the Image button if you feel I've been helpful.

“When you prepare for everything, you’re ready for anything.” - Bill Walsh


Top 
 Profile  
Reply with quote  
 Post subject: Re: Pin to PAP distances
 Posted: Sat Feb 03, 2018 10:25 am Post Number: #24 Post
Offline
Member

Joined: May 3, 2015
Posts: 54
Location: Cocoa Beach, FL
Reputation: 0
Reputation Power: 1
MegaMav wrote:
Cyclops: 80 x 5.5 x 45
Fix: Asym F - drill the fingers 3.5" deep, adjust VAL to 40.


Megamav,

Getting ready to drill these balls and I have one question, your recommendation for the Cyclops, is that with a MoTion hole like Eric and I were discussing? Or is it intended with no balance hole at all? Thanks.

_________________
Rob

RH Wiki Fit:
MF 4 7/16, 3/8 L, 1/8 R
RF 4 3/8, 1/2 R, 1/8 R
Thumb 1/4 Rev, 1/4 L
Axis Tilt 10 deg
Axis Rotation 70 deg
260 Revs
PAP 5 7/8 over 3/4 up
Speed 14.5 - 15.5 Monitor
House/Sport or PBA on rare occasion


Top 
 Profile  
Reply with quote  
 Post subject: Re: Pin to PAP distances
 Posted: Sat Feb 03, 2018 4:58 pm Post Number: #25 Post
Offline
Moderator
User avatar

Joined: April 26, 2007
Posts: 4246
Location: Malta, NY
Reputation: 933
Reputation Power: 10
rocketman1964 wrote:

Megamav,

Getting ready to drill these balls and I have one question, your recommendation for the Cyclops, is that with a MoTion hole like Eric and I were discussing? Or is it intended with no balance hole at all? Thanks.


Throw without a balance hole first.
Balance hole can be used to tune the reaction later.

_________________
Please press the Image button if you feel I've been helpful.

“When you prepare for everything, you’re ready for anything.” - Bill Walsh


Top 
 Profile  
Reply with quote  
 Post subject: Re: Pin to PAP distances
 Posted: Sat Feb 03, 2018 6:13 pm Post Number: #26 Post
Offline
Member

Joined: May 3, 2015
Posts: 54
Location: Cocoa Beach, FL
Reputation: 0
Reputation Power: 1
MegaMav wrote:

Throw without a balance hole first.
Balance hole can be used to tune the reaction later.


Understand, was planning on doing that. Just wasn’t sure if the layout on the Cyclops would allow for a MOtion hole. Thanks again for all your help.

_________________
Rob

RH Wiki Fit:
MF 4 7/16, 3/8 L, 1/8 R
RF 4 3/8, 1/2 R, 1/8 R
Thumb 1/4 Rev, 1/4 L
Axis Tilt 10 deg
Axis Rotation 70 deg
260 Revs
PAP 5 7/8 over 3/4 up
Speed 14.5 - 15.5 Monitor
House/Sport or PBA on rare occasion


Top 
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
 
Post new topic Reply to topic  [ 26 posts ]  Go to page Previous  1, 2

Board index » Mo & Friends » General Discussion


 
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to: