Search found 27 matches
- May 4th, 2010, 6:06 pm
- Forum: General Discussion
- Topic: Questions on Tendonitis
- Replies: 6
- Views: 961
you might try a arm band that goes around the fore arm just below the elbow. it about 2 or 3 in wide with velcrow to hold it in place. i had one for a couple months and it takes the presure off the elbow. it worked for me.
what are you refering to when you say preformance fit.i am not a jr bowler just don't know how to change it more like super senior but have just started drilling ball the last three yrs. love this site,very helpful.
i have been playing with my thumb pitch and yesterday i drill my vibe with 0* forward and 1/2* left pitch. i am right handed and my normal pitch was 1/4 rev and 1/8 right or palm. when i threw it ,it felt so good that i reslugged my mania and threw it last night, shot 189 258 257 left 2 ten pins 2nd...
i was told by a friend that i would get more reaction by drilling the bal hole deeper with a smaller bit in place of large bit and shallow hole . like a 3/4 in hole 3 in deep would be better then 1 inch hole 1-1/2 inches deep. any truth to that?
DRILLED THE BAL HOLE AS YOU SAID I TRYED IT AT 1000 AND THEN SCUFFED IT UP ABOUT 500 SEEMED TO WORK BETTER ON THE SPORT SHOT OR ARE NATIONAL PATERN HAVE TO HOLD A TIGHT LINE BUT IT CARRIES THE CORNER QUITE WELL . I STILL HAVE ROOM TO MAKE THE BAL HOLE A LITTLE LARGER OR DEEPER AND STILL BE LEGALE. P...
drilled the mania with out a bal hole it has 3/8 oz pos side and equal finger thumb.cannot swing it at all, high flush left 4-9 light hit left 5-7 and 8-10. thinking of hitting it with 500 it is at 2000 now. after i did that i thought i would put bal hole at p3 to give it 1/2 oz finger. any other ad...
Questions: Where is the balance hole in the Invasion and what are your personal specs as per the layout guide lines? bal hole is 1 inch 3in deep p3. my pap is over 5 over 1/2 up i am not sure of tilt and rev rate but plan to get that out in reno next mo. i was told they have a lane up stairs where ...
i drilled an invasion 80- 2 3/4 - 30 and was very satisfied with the result if i drill the mania the same should i not get nearly the same thing. from some spec i read the mania should be a little smother on the back. i drilled the mania with the double thumb and was not satisfied so i have pluged i...
- March 21st, 2010, 12:32 pm
- Forum: Layout Advice
- Topic: losing tilt and rotation to early
- Replies: 5
- Views: 1122
what grip change would you make to try and increase tilt or rotation my span is 4 1/4 middle 4 5/16 ring 1/8 forward finger 1/4 pitch middle 1/2 pitch ring 1/4 rev and 1/4 palm on the thumb.i tried reducing the thumb pitches but had trouble getting a smoth release.
i drilled this ball 50-4-35.his pap is 6 over up 1/4.the cg ended up 3 1/2 over just below mid line. when i scaled the ball i had 3 oz of side and 1/4 thumb.i drilled ring finger 3 in deep and put bal hole on p3.i drilled it 1 3/8 3 in deep to make legal. later i was reading some posts that said it ...
the fingers are 3 in deep my fingers are 29 and 13 so middle finger is drilled 1 1/32 they meet at the bottem of hole cg is 1 1/2 in left of line from pin to psa puts it near center of grip , bal hole is1 1/4 deep 31/32,i have 1/2 oz finger and 1/2 oz neg .when i measure between oil rings i have abo...
my pap is over5 up.5 i layed it out 58 x4 x 30 with 31/32 hole 1.5 in right of thumb. the cg of this ball was kicked to the left some i didn't measure it but it was a fair amount. when i drilled it i had to drill the fingers as deep as i could to stay under 1 oz finger wt. the bal hole is only 2 in ...
looking for some wisdom. i drilled the mania double thumb and the only way i can get it to turn the corner i have to put more angle of rotation then i am comfortable with. if i was to decrease the drill angle and the val would i not get the ball into the hook phase sooner and still get the same back...
- March 10th, 2010, 12:10 pm
- Forum: General Discussion
- Topic: Dual Angle, MB Properties & Int Diff
- Replies: 17
- Views: 3320
there are a lot of us in that spot i have a track 920a with close to a double thumb layout that will work on 38 to 40ft pat but if it is longer than that i am stuck from 10 board right. i will be drilling up a mania this weekend so i will let you know how it works. double thumb layout